conversion factor ucs to is

Correction Factors for Core Strengths| Concrete ...

The reason for applying a correction factor is that tall specimens tend to give lower test values than short specimens of the same cross-sectional area. In order to convert all core specimens to approximately the same strength basis as the standard 6x12-inch test cylinder, a correction factor is applied to the calculated strength.

GET PRICE

Conversion Factor Definition and Examples - ThoughtCo

 · A conversion factor is the number or formula you need to convert a measurement in one set of units to the same measurement in another set of units. The number is usually given as a numerical ratio or fraction that can be used as a multiplication factor.

GET PRICE

The Popperville Town Hall: How Much Are You Worth?

UCS supports the approach outlined in NUREG-1530, Rev. 1, to systematically review and update the conversion factors to keep them current by considering both changing economic conditions and new scientific developments. To that end, UCS agrees that the conversion factor should be expressed to two significant figures.

GET PRICE

An investigation of the accuracy of the use of point load ...

It has been observed by the authors that there is a very wide range in both the Is50 and UCS results for the Calp Limestone and that UCS values predicted from Is50 using a conversion factor of 21 to 24 can vary widely from actual UCS results from nearby samples.

GET PRICE

Point Load Test on Meta-Sedimentary Rocks and Correlation ...

Based on these testing results, a conversion factor between the UCS (BTS) and Is(50) of these two rock types can be obtained by using the regression equation (2). Table 3 shows the testing results and the corresponding conversion factors. The conversion factors for UCS of our studied metasedimentary rocks range between 20 and 21, which are 123 ...

GET PRICE

Estimating Rock Mass Strength - BM 1997 02

3 surface as a function of the normal stress is required. Procedures to deal with this obstacle will be discussed in Chapter 3 of this report. For intact rock, s = 1 and m = mi.Values for mi can be calculated from laboratory triaxial testing of core samples at different confining stress, or …

GET PRICE

granite ucs conversion factor - mannenkoorgent.be

granite ucs conversion factor - patelpackagingcoin. SPE 102781 - Stanford University uniaxial compressive strength (UCS) profile for the rocks the granite around the SAFOD well by Hickman and Z'obaclr10 SI Metric .

GET PRICE

INTERDEPENDENCE BETWEEN POINT LOAD INDEX, …

INTERDEPENDENCE BETWEEN POINT LOAD INDEX, COMPRESSIVE STRENGTH AND CRUSHING RESISTANCE OF JORDAN OIL SHALE AND ... and compressive strength were calculated. A conversion factor between PLTI and UCS for Jordan oil shale and dolostone was determined. ... Interdependence between Point Load Index, Compressive Strength and Crushing Resistance...

GET PRICE

The estimation of uniaxial compressive strength conversion ...

The point load (PL) test is generally used for estimation of uniaxial compressive strength (UCS) of rocks because of its economic advantages and simplicity in testing. If the PL index of a specimen is known, the UCS can be estimated using conversion factors.

GET PRICE

Dimensions, Units, Conversion Factors, and Significant Digits

Dimensions, Units, Conversion Factors, and Significant Digits . Introduction ; There is a difference between dimensions and units. A dimension is a measure of a physical variable (without numerical values), while a unit is a way to assign a number or measurement to that dimension.; For example, length is a dimension, but it is measured in units of feet (ft) or meters (m).

GET PRICE

Solved: What is the UCS Manager csv export time... - Cisco ...

Thanks to Walter who pointed me in the right direction, but didn't quite make it (out by a factor of 1000). SO to convert UCS Manager timestamps into current time (UTC), take the Created at time, divide it by 86,400,000 (=60*60*24*1000) then add to that "1/1/1970". IN excel, if your Created at time is in cell E2, enter the following into an ...

GET PRICE

USING THE POINT LOAD TEST TO DETERMINE THE UNIAXIAL ...

relationship between UCS and the point load strength could be expressed as: UCS = (K) Is50 = 24 Is50 (2) Where K is the "conversion factor." Subsequent studies found that K=24 was not as universal as had been hoped, and that instead there appeared to be a broad range of conversion factors. Table 1 summarizes published results obtained for ...

GET PRICE

(PDF) Figure 1. The Point Load Tester. USING THE POINT ...

This index can be used to estimate other rock strength parameters. The focus of this paper is to present the data analysis used to correlate the point load test index (Is50) with the uniaxial compressive strength (UCS), and to propose appropriate Is50 to UCS conversion factors for different coal measure rocks.

GET PRICE

Solved: Field conversion factor not ... - Autodesk Community

Re: Field conversion factor not working Ordinate dimensions rely on a "datum" point or "origin" to display the distance along the X or Y axis from that point to the feature you dimension. You might have noticed that when you placed the ordinate dimensions you were not prompted for a "first" point.

GET PRICE

Migrate to 40 Gbps with Cisco UCS Fabric Interconnects

provides a support matrix for conversion from 40-Gbps to 10-Gbps ports. Table 5. Support Matrix for Conversion from 40-Gbps to 10-Gbps Ports FI Model 40-Gbps Breakout Cable QSA Cisco UCS 6332 Ports 1 to 12 and 15 to 26 Ports 1 to 12 and 15 to 26 Cisco UCS …

GET PRICE

Utilizing the strength conversion factor in the estimation ...

Abstract. The strength conversion factor (k) is the ratio between the uniaxial compressive strength (UCS) and the point load index (PLI).It has been used to estimate the UCS from the PLI since the 1960s. Many researchers have investigated the relationship between UCS and PLI for various rock types of different geological origins, such as igneous, sedimentary, and metamorphic rocks.

GET PRICE

The NRC and the Value of Life - Union of Concerned Scientists

Pages 11-12 of NUREG-1530 give the discussion that selects $3 million as the value of a statistical life (section 6.6) and relates the $3 million value to a conversion factor of $2100 per person-rem, which it then rounds down to $2000 per person-rem (section 8).

GET PRICE

Stress and Pressure Conversion (Online Units Converter)

Online converter for units of stress and pressure. Bar, pascal, PSI, or inch of mercury? Instantly convert any unit to all others.

GET PRICE

Oracle Processor Core Factor Table

On 12/01/2010, changed the Core Processor Licensing Factor for Intel Itanium Series 93XX from 0.5 to 1.0. Also added notes in parenthesis to the affected rows in the table above On 11/05/2014, added Intel Xeon Series E5-26XX v3, E5-24XX v2, E5-16XX v3 and E5-16XX v2 chips with a core factor of 0.5

GET PRICE

Point load test application for estimating compressive ...

UCS indirectly, index-to-strength conversion factors are constructed (ISRM, 1985). Richardson (1989) conducted a point load tests of cast specimens with various diameters as 50.8, 76.2 and 101.6mm. The advantages of using the point load test relate to a smaller cost per unit test when compared to

GET PRICE